1 HP Submersible Pump: Types, Uses and Price in India

Men standing in a flooded street after heavy rain, when submersible pumps are used to drain basements and pits

By Btali Technical Team · Updated 4 November 2026 · Prices checked against Btali product pages on 4 November 2026

Quick answer: A 1 HP submersible pump has a motor of about 0.75 kW that sits under water and pushes water up and out. The Btali 1 HP models list a maximum flow of 300 to 380 litres per minute and a maximum head (lift) of 10 metres, which suits draining sumps, basements, lift pits, underground tanks, construction pits and sewage chambers. They use about 0.7 to 0.75 units of electricity per hour of running. On 4 November 2026, the Btali BT-750 1 HP sewage pump cost ₹12,935 and the stainless steel BT700 1 HP dewatering pump ₹19,537.

Men standing in a flooded street after heavy rain, when submersible pumps are used to drain basements and pits
Monsoon waterlogging is when most buildings find out whether their sump and basement pumps are big enough. Photo: Unsplash.

One thing to settle first: there are two very different kinds of "1 HP submersible pump" in India. Borewell pumps are long, slim pumps lowered deep into a narrow borewell. Drainage, sewage and dewatering pumps are compact units that sit at the bottom of a sump, tank or pit. Btali makes the second kind. If you need to lift water from a deep borewell, you need a borewell pump; if you need to empty, drain or transfer water from a pit, tank or chamber, read on.

What 1 HP actually gives you

  • Power: 1 HP is about 0.75 kW. The Btali BT-750 lists 750 W and the BT700 lists 700 W.
  • Maximum head: both list 10 m. That is the height at which the pump can just hold water up with no flow. In practice you get useful flow at lifts well below that.
  • Maximum flow: 300 L/min (BT-750) and 380 L/min (BT700). That is the flow with almost no lift. As the lift increases, flow drops.
  • Running cost: about 0.75 units per hour. At an example tariff of ₹8 per unit, that is about ₹6 per hour of running.

A simple way to think about head and flow: the higher you push water, the less of it comes out. If you need to lift water close to 10 m, a 1 HP pump will move only a trickle; step up to 1.5 or 2 HP.

Btali 1 HP submersible pumps compared

ModelTypePowerMax headMax flowWeightFloat switchPrice (as of 4 Nov 2026)
BT-750Sewage1 HP, 750 W10 m300 L/min17.5 kgYes₹12,935
BT700Dewatering, stainless steel1 HP, 700 W10 m380 L/min18.5 kgYes₹19,537

Specs and sale prices as listed on btaliinternational.com on 4 November 2026. Both run at 2,860 RPM according to their product pages.

For comparison, the next sizes down and up:

ModelPowerMax headMax flowPrice (as of 4 Nov 2026)
BT-2500.5 HP, 375 W7.5 m150 L/min₹9,066
BT-1100 Eco Series sewage1.5 HP, 1,100 W10 m350 L/min₹13,173
BT-1100 sump1.5 HP, 1,100 W10 m350 L/min₹17,358

Btali BT700 1 HP stainless steel submersible dewatering pump with float switch

Bar chart comparing listed maximum flow, head and price of Btali 0.5 HP, 1 HP and 1.5 HP submersible pumps
Chart by the Btali Technical Team from listed specs and prices on btaliinternational.com, 4 November 2026.

Types of 1 HP submersible pump

Sewage pump (BT-750)

Built to handle dirty water from toilets, kitchens and drains, collected in a sewage or septic chamber. The float switch starts the pump when the level rises and stops it when the chamber is empty. Use it for building sewage sumps, hotel and restaurant drains, and basement toilets below the main sewer line. For heavier sewage with rags and solids, a cutter pump is the safer choice; our submersible sewage pump guide explains when.

Dewatering pump (BT700)

Built to clear relatively clean or muddy water quickly: flooded basements, lift pits, construction excavations, underground water tanks being cleaned, and rainwater pits during the monsoon. The BT700 has a stainless steel body, which resists corrosion in water that sits in the pit for long periods, and it lists the highest flow of our 1 HP pumps at 380 L/min.

Where a 1 HP submersible pump fits

  • Emptying an underground water tank for cleaning
  • Keeping a basement or lift pit dry in the monsoon
  • Draining a building’s sewage collection chamber
  • Dewatering a foundation pit on a small construction site
  • Transferring water between tanks at a similar level
  • Clearing a waterlogged garden, lawn or courtyard

Choosing between 0.5 HP, 1 HP and 1.5 HP

SituationSize
Small tank or shallow pit, lift under 5 m, light use0.5 HP (BT-250)
Typical building sump, basement or chamber, lift up to about 6 m1 HP (BT-750 or BT700)
Higher lift, bigger chamber or faster emptying needed1.5 HP (BT-1100) or 2 HP

When in doubt, measure the vertical height from the water surface to the discharge point and add a little for long pipe runs and bends. If that height is close to 10 m, choose a bigger pump.

Installation tips

  1. Stand the pump on a firm, level base, slightly raised from the bottom so it does not suck in settled sludge.
  2. Make sure the float switch can move freely and is not trapped against the wall or pipe.
  3. Use discharge pipe of the size the outlet is designed for; a narrower pipe cuts flow.
  4. Fit a non-return valve if water could flow back into the pit when the pump stops.
  5. Have an electrician fit a correctly rated switch and protection; check the supply on the product page or nameplate before connecting.
  6. Never lift or lower the pump by its cable; use a rope or chain on the handle.

1 HP submersible pump price in India

On 4 November 2026, the Btali BT-750 1 HP sewage pump with float was ₹12,935 and the stainless steel BT700 1 HP dewatering pump kit with float was ₹19,537. Prices for other sizes, from 0.25 HP to 10 HP, are in our submersible pump price guide.

Frequently asked questions

How much water does a 1 HP submersible pump give per hour?

The Btali 1 HP pumps list a maximum of 300 L/min (BT-750) and 380 L/min (BT700), which is 18,000 to 22,800 litres per hour at close to zero lift. At higher lifts the flow is lower.

How high can a 1 HP submersible pump lift water?

Both Btali 1 HP pumps list a maximum head of 10 m. For steady, useful flow, plan for lifts comfortably below that.

Can I use a 1 HP submersible pump in a borewell?

Not these models. Borewell pumps are slim units designed to go down narrow bores. The Btali 1 HP pumps are for sumps, tanks, pits, basements and sewage chambers.

How much electricity does a 1 HP submersible pump use?

About 0.7 to 0.75 units per hour of running, based on the listed 700 W and 750 W motors. With a float switch, it only runs when there is water to pump.

What is a float switch on a submersible pump?

A float switch rises with the water level and starts the pump automatically, then stops it when the level falls. It prevents dry running and saves you from switching the pump on and off by hand.

Next steps

Measure the lift and the size of the pit or chamber, then compare models on the submersible pump page. If you are choosing between single-phase and three-phase pumps, read our single phase vs three phase guide. For help, call +91 77109 21153.

About the Btali Technical Team

The Btali Technical Team is the product and service group at Btali International, Mumbai. We have worked with water and air equipment for over 20 years, and the company is ISO 9001:2015 and CRISIL certified, with a dealer and service network across India. Specs and prices in this guide come from our own product pages. More about Btali International.

One thought

Leave a Reply

Your email address will not be published. Required fields are marked *

Let's Chat

Enquiry Form

Dealership Enquiry Form